ww-audio

Forum Replies Created

Viewing 10 posts - 1 through 10 (of 10 total)

Posted In:


  • Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #51534

    Hello there
    More than 100 concerts meanwhile, they all survived.
    Up to 200 people, even with rock.
    I love them
    cheers
    Werner


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11090

    [attachment=0:2wn6aue4]FOH-1.jpg[/attachment:2wn6aue4]They (together with the 15″ Subs) survived their first concert (180 persons) yesterday, great transparent sound, loud an clear and never agressiv.
    All in all my suggestion for small Club gigs.
    cheers
    Werner


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11089

    [attachment=0:ky991fyo]Toleranz-1.JPG[/attachment:ky991fyo][attachment=1:ky991fyo]Midas-TPL-AE-Powersoft.JPG[/attachment:ky991fyo]Hi all, Hi Stryke
    Congratulaions on your products again … her a pic of 2 TDM12M, just a testing measuremet ..


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11088

    [attachment=0:3vvplg1h]Final.JPG[/attachment:3vvplg1h]Final Response. Quite nice for PA :mrgreen:

    this was at about 95 db … if you can trust a iPod app ….


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11087

    [attachment=0:2bt0l73y]Foto.jpg[/attachment:2bt0l73y]Finished and tested in our rehearsel room, just perfekt.


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11086

    Hello stryke
    Hm, thats difficult to say, I will have to set up a decent callibration of my whole Setup (as you ca see on the Picture I’m using a focusrite (line Level calibrated) with variable mic gain, for measuring the the new presonus mic .
    From my experience it is something like near 120 db … impossible to stand without hearing protection … and it still sounded with them on :mrgreen:
    As we have carneval tommorow it’s a good opportunity th run it outside the house for long time testing :mrgreen:
    cheers
    Werner

    Sorry, have to be more specific. The about 120 dB are full power, did not measure Distorsion at that level.


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11084

    Hi all
    So here is the measuring at full power with some drops as you need it for (small) PA
    Just watch the thd for the tdm, amazing, same level as the tdm ….crossover at 1600 Hz, so ther should be no worry to grill the tpl 😛
    Low (LR 48) cut for the tdm at 50Hz
    sounds like a headphone …


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11082

    [attachment=0:dcoqy69r]IMG_0355.JPG[/attachment:dcoqy69r]Hello John and srtyke
    Frequency Response of your Driver as predicted.
    This not a PA Top but a High-End Top at jet level. Amazing, almost no power compression, it remains allmost balanced with the tpl at full power …
    Can’t wait to finish the pair
    Congratulations for your product
    cheers
    Werner


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11081

    Hi stryke
    I’m powering the PAS with the IS-Modules described above. It is amazing what you get out of it, combined with a BMS 15N840 woofer with it’s own IS.
    So please, work on it and let me hear 🙂
    cheers
    Werner


    Participant
    ww-audio on · in reply to: Which TD12 for 3 Way PA? #11079

    Hello John
    Thanks for yor reply. I will build a new box und use the 4-Channel DCell bridged, so I will get 700 Watts out of it for the td12 and the tpl 150H each at 8 ohms :mrgreen:
    The PAS Coax are boomy, strange phase behaviour in the low mids … you can flatten the response with a decent controller as in the DCell but then you run into problems at about 800 Hz.
    If you manage to improve that, please let me know, we (me and my collegue) own 8 pieces of them.
    I ordered 2 TD12 yesterday, I will post the results.
    Best regards
    Werner

Viewing 10 posts - 1 through 10 (of 10 total)