rajacat

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 23 total)

Posted In:


  • Member
    rajacat on · in reply to: stock rubber gasket #11291

    Hmm…. 💡 Has anyone cut the inside ring out of the rubber gasket so that its not between the mounting flange and the baffle? I was thinking that I could use the rubber gasket for strictly cosmetics while replacing the the inner ring with a proper closed cell gasket material. I wonder if the modified rubber gasket would stay in place by just shoving into gap between the driver and the sides of the recessed cutout?


    Member
    rajacat on · in reply to: stock rubber gasket #11289

    @zedguy wrote:

    I always throw away the rubber trim ring and use foam tape as a gasket.

    Unfortunately, I have already cut and designed the TD15M baffle so that the depth of the recess accounts for the rubber ring. The ring fits like a glove. The driver will look a little odd recessed a bit over 1/2″ into the face of the baffle without the rubber trim ring. The baffle is already finished with high gloss paint so routering a bullnose to get rid of the sharp edge is questionable.
    I’ve been thinking that the rubber ring is overly resilient so as to absorb too much energy from the driver. What’s the use of constructing a very stiff baffle (1-7/8″) when that stiffness is lessened by the use of the rubber?

    Am I over thinking this? Analysis paralysis? 🙄


    Member
    rajacat on · in reply to: NEW TD15H+ #10919

    Apparently nobody from AE is tending the company forum 🙄 . Probably better off asking the question on the AVS forum.


    Member
    rajacat on · in reply to: Phase plug fabrication status updates? #10681

    @markkmueller wrote:

    I placed my TD15M order on 23 Feburary, 1012 and I’m still waiting for the phase plugs. My order number was: 901. Is it going to be a long wait for more to be shipped?

    Thanks,
    Mark

    Mark,

    send an email to Jana. info(at)aespeakers.com

    My Group Buy One phase plugs are in the mail. Due Monday.

    …Roy


    Member
    rajacat on · in reply to: Phase plug fabrication status updates? #10676

    @stryke wrote:

    We shipped out all of the TD12 phase plugs and most all of the TD15 phase plugs last week from people that were on the list to need them. Check your email for the UPS tracking numbers. About 40 total went out and we ran out. We are finding a few others needing them that weren’t noted in the system so they are being added as we are informed about them.

    John

    I still haven’t received the UPS tracking numbers.

    Roy


    Member
    rajacat on · in reply to: Phase plug fabrication status updates? #10677

    @stryke wrote:

    We shipped out all of the TD12 phase plugs and most all of the TD15 phase plugs last week from people that were on the list to need them. Check your email for the UPS tracking numbers. About 40 total went out and we ran out. We are finding a few others needing them that weren’t noted in the system so they are being added as we are informed about them.

    John

    I must be one of those few. I’ll PM you my email address so you’ll know who I am.

    Thanks


    Member
    rajacat on · in reply to: Phase plug fabrication status updates? #10678

    Any progress on the phase plugs for Group Buy 1?


    Member
    rajacat on · in reply to: ** Official TD Woofer Group Buy Information ** #9804

    Any update on shipping date for the Group Buy TD15M phase plugs ?

    Thanks


    Member
    rajacat on · in reply to: Displacement #10499

    Simon,
    Do you know the rear displacement of the TD15M? I’m also curious how you came up with the 0.1cu. ft. number for the TD12.

    Thanks


    Member
    rajacat on · in reply to: ** Official TD Woofer Group Buy Information ** #9735

    Wow! That looks like enough steel for a lot of drivers. :mrgreen:


    Member
    rajacat on · in reply to: ** Official TD Woofer Group Buy Information ** #9727

    @stryke wrote:

    Just received the arrival notice a few minutes ago. The container arrives in Long beach on 6/5 and is set to arrive in Chicago on 6/10. It clears customs after it arrives in Chicago so I will update again when that happens and the parts are in route to Green Bay. There is no guaranteed time for the customs clearance. Some people have had significant delays and other times things move quite smoothly.

    John

    That’s terrific news!! :mrgreen:


    Member
    rajacat on · in reply to: ** Official TD Woofer Group Buy Information ** #9715

    @stryke wrote:

    Wanted to give another quick update. The goods were delivered to the docks last week as expected. The container leaving for Chicago ultimate destination was set to leave on May 22 which is today. I should have confirmation that it is on the water soon.

    John

    Excellent! :mrgreen:


    Member
    rajacat on · in reply to: ** Official TD Woofer Group Buy Information ** #9714

    Thanks for the update/information.

    -Roy


    Member
    rajacat on · in reply to: ** Official TD Woofer Group Buy Information ** #9712

    Re: ** Official TD Woofer Group Buy Information **

    Postby stryke » Tue Apr 10, 2012 7:24 pm
    In addition, everyone who has made payment for the drivers on the group buy will be getting an email to confirm their order shortly. I have noticed that the impedance and S/X/H/M designation was left off on some of the invoices. I want to verify personally that everyone is getting the right woofers.

    John
    ***************************************
    When will we get the email confirming our orders and confirming the impedance and model designation? It’s been a month. 🙄


    Member
    rajacat on · in reply to: ** Official TD Woofer Group Buy Information ** #9698

    In reality, a receipt for my PayPal payment should have been issued “shortly” after acceptance by AE. That would have been about 5 months ago. 🙄 This is standard procedure for any legitimate business.

Viewing 15 posts - 1 through 15 (of 23 total)